Ubuntu 18.04: Disable Netplan switch back to networking /etc/network/interfaces Rumi, February 24, 2020June 17, 2020 The following procedure works for Ubuntu 18.04 (Bionic Beaver) I. Reinstall the ifupdown package: # apt-get update # apt-get install ifupdown II. Configure your /etc/network/interfaces file with configuration stanzas such as: source /etc/network/interfaces.d/* # The loopback network interface auto lo iface lo inet loopback allow-hotplug enp0s3 auto enp0s3 iface enp0s3 inet static address 192.168.1.133 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 # Only relevant if you make use of RESOLVCONF(8) # or similar... dns-nameservers 1.1.1.1 1.0.0.1 III. Make the configuration effective (no reboot needed): # ifdown --force enp0s3 lo && ifup -a # systemctl unmask networking # systemctl enable networking # systemctl restart networking IV. Disable and remove the unwanted services: # systemctl stop systemd-networkd.socket systemd-networkd \ networkd-dispatcher systemd-networkd-wait-online # systemctl disable systemd-networkd.socket systemd-networkd \ networkd-dispatcher systemd-networkd-wait-online # systemctl mask systemd-networkd.socket systemd-networkd \ networkd-dispatcher systemd-networkd-wait-online # apt-get --assume-yes purge nplan netplan.io Then, you’re done. Note: You MUST, of course, adapt the values according to your system (network, interface name…). V. DNS Resolver Because Ubuntu Bionic Beaver (18.04) make use of the DNS stub resolver as provided by SYSTEMD-RESOLVED.SERVICE(8), you SHOULD also add the DNS to contact into the /etc/systemd/resolved.conf file. For instance: .... DNS=1.1.1.1 1.0.0.1 .... and then restart the systemd-resolved service once done: # systemctl restart systemd-resolved The DNS entries in the ifupdown INTERFACES(5) file, as shown above, are only relevant if you make use of RESOLVCONF(8) or similar. Src: https://askubuntu.com/questions/1031709/ubuntu-18-04-switch-back-to-etc-network-interfaces Related Administrations Configurations (Linux) NetplanNetworkingUbuntu 18
Install Docker on Debain 10 December 21, 2021 Installing Docker The Docker installation package available in the official Debian repository may not be the latest version. To ensure we get the latest version, we’ll install Docker from the official Docker repository. To do that, we’ll add a new package source, add the GPG key from Docker to ensure… Read More
Nginx upstream timed out April 22, 2018 There are two main directives responsible for Nginx upstream timed out (110: Connection timed out) error: proxy_read_timeout – Defines a timeout for reading a response from the proxied server. Default is 60 seconds. location ~ ^/slow-proxy { proxy_read_timeout 180; # <— proxy_pass …; } * you can use proxy_read_timeout inside… Read More
Auto installation of Zenoss on CentOS 6 June 19, 2016 The simplest way to install Zenoss Core 4.2 on a newly-deployed RHEL/CentOS 64-bit 5/6 system is to use our auto-deploy script, which downloads all required files for you. To use the script, first set up a new server running one of our supported operating systems. Then, as root, run the… Read More
If you copy something, it would be worth mentioning. https://askubuntu.com/questions/1031709/ubuntu-18-04-switch-back-to-etc-network-interfaces Reply
I usually keep the content credit source if it’s collected or copied from somewhere else. If you read the other posts you should find them in usual footer credit content src link. However, sometimes the source link are a bit lost while I work multiple workstation terminal. I’m updating this particular post. Reply
I somehow managed to break the neworking completely by trying to enable this. Any pointers to get this back to a stable environment? Reply