Ubuntu 18.04: Disable Netplan switch back to networking /etc/network/interfaces Rumi, February 24, 2020June 17, 2020 The following procedure works for Ubuntu 18.04 (Bionic Beaver) I. Reinstall the ifupdown package: # apt-get update # apt-get install ifupdown II. Configure your /etc/network/interfaces file with configuration stanzas such as: source /etc/network/interfaces.d/* # The loopback network interface auto lo iface lo inet loopback allow-hotplug enp0s3 auto enp0s3 iface enp0s3 inet static address 192.168.1.133 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 # Only relevant if you make use of RESOLVCONF(8) # or similar... dns-nameservers 1.1.1.1 1.0.0.1 III. Make the configuration effective (no reboot needed): # ifdown --force enp0s3 lo && ifup -a # systemctl unmask networking # systemctl enable networking # systemctl restart networking IV. Disable and remove the unwanted services: # systemctl stop systemd-networkd.socket systemd-networkd \ networkd-dispatcher systemd-networkd-wait-online # systemctl disable systemd-networkd.socket systemd-networkd \ networkd-dispatcher systemd-networkd-wait-online # systemctl mask systemd-networkd.socket systemd-networkd \ networkd-dispatcher systemd-networkd-wait-online # apt-get --assume-yes purge nplan netplan.io Then, you’re done. Note: You MUST, of course, adapt the values according to your system (network, interface name…). V. DNS Resolver Because Ubuntu Bionic Beaver (18.04) make use of the DNS stub resolver as provided by SYSTEMD-RESOLVED.SERVICE(8), you SHOULD also add the DNS to contact into the /etc/systemd/resolved.conf file. For instance: .... DNS=1.1.1.1 1.0.0.1 .... and then restart the systemd-resolved service once done: # systemctl restart systemd-resolved The DNS entries in the ifupdown INTERFACES(5) file, as shown above, are only relevant if you make use of RESOLVCONF(8) or similar. Src: https://askubuntu.com/questions/1031709/ubuntu-18-04-switch-back-to-etc-network-interfaces Related Administrations Configurations (Linux) NetplanNetworkingUbuntu 18
CentOS 7 XFS disk resizing June 4, 2021 Couldn’t find any article that explained step by step how to resize the main disks volume in a CentOS 7 vm. In my example I started witha single disk of 8GB and expanded to 20GB. I have two partitions on disk sda sda1 type Linux for boot sda2 type Linux… Read More
Install Redis Server and PHP-Redis on Debian or Ubuntu System April 20, 2018 you can install the phpredis extension from the Ubuntu respositories. First, if you don’t have it installed already, let’s install Redis: sudo apt-get install redis-server After we get Redis installed (and/or verified that it was installed), we can install the PHP module for Redis: sudo apt-get install php5-redis After the module is… Read More
Format a Hard Drive Using the windows Command Prompt March 6, 2020 STEP 1: Open Command Prompt As Administrator Opening the command prompt. Search for command prompt, right click and run as Administrator. Related Read More
If you copy something, it would be worth mentioning. https://askubuntu.com/questions/1031709/ubuntu-18-04-switch-back-to-etc-network-interfaces Reply
I usually keep the content credit source if it’s collected or copied from somewhere else. If you read the other posts you should find them in usual footer credit content src link. However, sometimes the source link are a bit lost while I work multiple workstation terminal. I’m updating this particular post. Reply
I somehow managed to break the neworking completely by trying to enable this. Any pointers to get this back to a stable environment? Reply